IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 95 / 170

AFL-xxA-N270 Series Panel PC

Page 81

The

CPU Temp. Limit of Start

option can only be set if the

CPU FAN Mode Setting

option is set to

Automatic Mode

. Use the

CPU Temp. Limit of Start

option to select the

CPU temperature at which the cooling fan should automatically turn on. When the fan

starts, it rotates using the starting pulse width modulation (PWM) specified in the

Fan 3

Start PWM

option below. To select a value, select the

CPU Temp. Limit of Start

option

and enter a decimal number between 000 and 127. The temperature range is specified

below.

Minimum Value: 0°C

Maximum Value: 127°C

CPU Fan Start PWM [070]

The

Fan 3 Start PWM

option can only be set if the

CPU FAN Mode Setting

option is set

Automatic Mode

. Use the

Fan 3 Start PWM

option to select the PWM mode the fan

starts to rotate with after the temperature specified in the

Temperature 3 Limit of Start

exceeded. The Super I/O chipset supports 128 PWM modes. To select a value, select the

Fan 3 Start PWM

option and enter a decimal number between 000 and 127. The

temperature range is specified below.

PWM Minimum Mode: 0

PWM Maximum Mode: 127

Slope PWM [0.5 PWM]

The

Slope PWM 1

option can only be set if the

CPU FAN Mode Setting

option is set to

Automatic Mode

. Use the

Slope PWM 1

option to select the linear rate at which the PWM

mode increases with respect to an increase in temperature. A list of available options is

shown below:

0.125

PWM

0.25

PWM

0.5

PWM

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды