IEI Technology AFL A-N270 Series Скачать руководство пользователя страница 86

Страница: 86 / 170

AFL-xxA-N270 Series Panel PC

Page 72

6.3.2.1 IDE Master, IDE Slave

Use the

IDE Master

and

IDE Slave

configuration menu to view both primary and

secondary IDE device details and configure the IDE devices connected to the system.

BIOS Menu 5: IDE Master and IDE Slave Configuration

Auto-Detected Drive Parameters

The “grayed-out” items in the left frame are IDE disk drive parameters automatically

detected from the firmware of the selected IDE disk drive. The drive parameters are listed

as follows:

Device

: Lists the device type (e.g. hard disk, CD-ROM etc.)

Type

: Indicates the type of devices a user can manually select

Vendor

: Lists the device manufacturer

Size

: List the storage capacity of the device.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Бренды по названию

Популярные бренды