IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 44 / 170

AFL-xxA-N270 Series Panel PC

Page 30

Anti-static Discharge

: If a user open the rear panel of the flat panel PC, to

configure the jumpers or plug in added peripheral devices, ground themselves

first and wear and anti-static wristband.

4.3 Preinstalled Components

The following components are all preinstalled.

Motherboard

TFT LCD screen

1.0 GB DDR2 memory module

Resistive type touch screen

Wireless LAN module

Bluetooth

module

AT/ATX power switch

Hard disk drive (HDD)

Preinstalled customizations may include the following.

Different DDR2 memory module

Hard disk drive (AFL-12A-N270 only)

Component installation is described in

the following sections.

4.4 Installation and Configuration Steps

The following installation steps must be followed.

Step 1:

Unpack the flat panel PC

Step 2:

Install a CF card

Step 3:

Install a HDD (AFL-12A-N270 only)

Step 4:

Configure the system

Step 5:

Connect peripheral devices to the bottom panel of the flat panel PC

Step 6:

Mount the flat panel PC

Step 0:

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды