IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 38 / 170

AFL-xxA-N270 Series Panel PC

Page 24

3.1 Unpacking

To unpack the flat panel PC, follow the steps below:

WARNING!

The front side LCD screen has a protective plastic cover stuck to the

screen. Only remove the plastic cover after the flat panel PC has been

properly installed. This ensures the screen is protected during the

installation process.

Step 1:

Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

external (second) box.

Step 2:

Open the external (second) box.

Step 3:

Use box cutters, a knife or a sharp pair of scissors that seals the top side of the

internal (first) box.

Step 4:

Lift the monitor out of the boxes.

Step 5:

Remove both polystyrene ends, one from each side.

Step 6:

Pull the plastic cover off the flat panel PC.

Step 7:

Make sure all the components listed in the packing list are present.

Step 0:

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды