IEI Technology AFL A-N270 Series Скачать руководство пользователя страница 31

Страница: 31 / 170

AFL-xxA-N270 Series Panel PC

Page 17

Supports IEEE 802.1Q VLAN tagging

Serial

EEPROM

Transmit/Receive on-chip buffer support

64-pin QFN package (Green package)

2.4.3 External USB Connectors

There are two USB 2.0 connectors on the bottom panel of the AFL-xxA-N270. Both USB

2.0 connectors are interfaced directly to the USB controllers on the ICH7-M southbridge.

These USB connectors are fully compliant with USB specification Revision 2.0 and USB

specification Revision 1.1 and can be interfaced to both USB 1.1 and USB 2.0 compliant

devices.

Figure 2-8: External USB Ports

2.5 AFOLUX AFL-xxA-N270 Front Side

2.5.1 Monitor

A LCD screen is installed on the front of the AFOLUX AFL-xxA-N270 series. The monitor

maximum resolution is varied in different AFL-xxA-N270 models. The screen is shown in

Figure 2-9

below.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Бренды по названию

Популярные бренды