IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 119 / 170

AFL-xxA-N270 Series Panel PC

Page 105

7.1 Available Software Drivers

NOTE:

The content of the CD may vary throughout the life cycle of the product

and is subject to change without prior notice. Visit the IEI website or

contact technical support for the latest updates.

The following drivers can be installed on the system:

Chipset

VGA

LAN

Touch

screen

Audio

Wireless

Bluetooth

Installation instructions are given below.

7.2 Starting the Driver Program

To access the driver installation programs, please do the following.

Step 1:

Insert the CD-ROM that came with the system into a CD-ROM drive attached to

the system.

Step 2:

Click

AFLMB-945GSE-N270-R10 Driver

Step 3:

The list of drivers in

Figure 7-1

appears.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды