IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 116 / 170

AFL-xxA-N270 Series Panel PC

Page 102

BIOS Menu 20:Exit

Save Changes and Exit

Use the

Save Changes and Exit

option to save the changes made to the BIOS options

and to exit the BIOS configuration setup program.

Discard Changes and Exit

Use the

Discard Changes and Exit

option to exit the BIOS configuration setup program

without saving the changes made to the system.

Discard Changes

Use the

Discard Changes

option to discard the changes and remain in the BIOS

configuration setup program.

Load Optimal Defaults

Use the

Load Optimal Defaults

option to load the optimal default values for each of the

parameters on the Setup menus.

F9 key can be used for this operation.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды