IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 109 / 170

AFL-xxA-N270 Series Panel PC

Page 95

AddOn ROM Display Mode [Force BIOS]

The

AddOn ROM Display Mode

option allows add-on ROM (read-only memory)

messages to be displayed.

Force BIOS

EFAULT

Allows the computer system to force a third party

BIOS to display during system boot.

Keep Current

Allows the computer system to display the

information during system boot.

Bootup Num-Lock [On]

The

Bootup Num-Lock

BIOS option allows the Number Lock setting to be modified

during boot up.

Off

Does not enable the keyboard Number Lock automatically. To

use the 10-keys on the keyboard, press the Number Lock key

located on the upper left-hand corner of the 10-key pad. The

Number Lock LED on the keyboard lights up when the Number

Lock is engaged.

On D

EFAULT

Allows the Number Lock on the keyboard to be enabled

automatically when the computer system boots up. This allows

the immediate use of the 10-key numeric keypad located on

the right side of the keyboard. To confirm this, the Number

Lock LED light on the keyboard is lit.

Boot From LAN Support [Disabled]

The

BOOT From LAN Support

option enables the system to be booted from a remote

system.

Enabled

Can be booted from a remote system through the

LAN

Disabled D

EFAULT

Cannot be booted from a remote system through the

LAN

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды