IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 103 / 170

AFL-xxA-N270 Series Panel PC

Page 89

Disabled

The console is not redirected after POST

Boot Loader

Redirection is active during POST and during Boot

Loader

Always D

EFAULT

Redirection is always active (Some OSes may not

work if set to Always)

Terminal Type [ANSI]

Use the

Terminal Type

BIOS option to specify the remote terminal type.

ANSI D

EFAULT

The target terminal type is ANSI

VT100

The target terminal type is VT100

VT-UTF8

The target terminal type is VT-UTF8

6.3.8 USB Configuration

Use the

USB Configuration

menu (

BIOS Menu 12

) to read USB configuration

information and configure the USB settings.

BIOS Menu 12: USB Configuration

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды