IEI Technology AFL A-N270 Series Скачать руководство пользователя

Страница: 102 / 170

AFL-xxA-N270 Series Panel PC

Page 88

Serial Port Number [COM1]

Use the

Serial Port Number

option allows to select the serial port used for remote

access.

COM1 D

EFAULT

System is remotely accessed through COM1

COM2

System is remotely accessed through COM2

COM3

System is remotely accessed through COM3

NOTE

: Make sure the selected COM port is enabled through the Super I/O configuration

menu.

Base Address, IRQ [3F8h,4]

The

Base Address, IRQ

option cannot be configured and only shows the interrupt

address of the serial port listed above.

Serial Port Mode [115200 8,n,1]

Use the

Serial Port Mode

option to select baud rate through which the console redirection

is made. The following configuration options are available

115200

8,n,1

EFAULT

57600

8,n,1

38400

8,n,1

19200

8,n,1

09600

8,n,1

NOTE:

Identical baud rate setting musts be set on the host (a management

computer running a terminal software) and the slave.

Redirection After BIOS POST [Always]

Use the

Redirection After BIOS POST

option to specify when console redirection should

occur.

Содержание AFL A-N270 Series











































































































































































Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды

IEI Technology AFL A-N270 Series, Руководство пользователя

Результаты поиска

Содержание AFL A-N270 Series

Отзывы:

Похожие инструкции для AFL A-N270 Series

Бренды по названию

Популярные бренды