IEC miniReStoramod Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 28

IEC miniReStoramod Скачать руководство пользователя страница 24

Modular Hi-Rise Replacement Series – MIY

INSTALLATION, OPERATION, & MAINTENANCE MANUAL

24

SECTION FIVE — Routine Maintenance, Cont’d.

Replacement Parts

OEM replacement parts should be used wherever
possible to maintain unit performance, its normal
operating characteristics, and the testing agency listings.
Replacement parts may be purchased through a local
sales representative which may be found by using the Rep
Locator tab on the IEC website (www.iec-okc.com).

Contact the local sales representative or the factory before
attempting any unit modifications. Any modifications not
authorized by the factory could result in personal injury,
damage to the unit, and could void all factory warranties.
When ordering parts, the following information must be
supplied to ensure proper part identification:

(1)  Complete unit model number
(2)  Unit serial number
(3)  Unit hand connection (right or left hand)
(4)  Complete part description including any numbers

On warranty replacements, in addition to the information
previously listed, the unit shipping code which appears
on the upper right-hand corner of the serial plate is
required. Contact the factory for authorization to return
any parts, such as defective parts replaced in warranty. All
shipments returned to the factory must be marked with
a Return Authorization Number, which is provided by the
factory.

All equipment and components sold through the Parts
Department are warranted under the same conditions as
the standard manufacturer’s warranty with the exception
that the warranty period is twelve (12) months, unless the
component is furnished as a warranty replacement. Parts
furnished as warranty replacements are warranted for the
remaining term of the original unit warranty, or not less
than thirty (30) days.

Please refer to the Factory website for a general Service-
Parts Manual. Unit-specific parts can be identified by your
local IEC sales representative by using the “Replacement
Parts” QR code label on the unit with a smartphone app,
or by directly contacting the factory (405-605-5000).

«
...
22
23
24
25
26
...
»

Содержание miniReStoramod





























Отзывы:

Нет отзывов