IDTECK iMDC-MAIN Скачать руководство пользователя страница 46

Страница: 46 / 79

NETWORK SETTING

p.40

PUBLIC IP NETWORK SETTING

Above figure is the configuration using public IP broadband.

If you use the same public IP broadband, it is possible to search all of the iMDC-MAIN, iMDC

-RIM board connected on the same network by using automatic searching function of STAR

TWHATCH ENTERPRISE or iMDC EMULATOR. (Please refer to ‘6.Network setting’, ‘7.iMDC E

MULATOR’)

But if you use different IP broadband, it is possible to search the information of the iMDC-M

AIN, iMDC-RIM board by manual searching function.

If firewall of PC blocks the port used for iMDC-MAIN and iMDC-RIM (iMDC-MAIN, iMDC-RI

M, communication server), Set the firewall cancellation about the ports. Otherwise the firew

all may block the applicable ports used to communicate with STARWATCH ENTERPRISE.

2.1

iMDC-MAIN IP ADDRESS SETTING

STARTWATCH ENTERPRISE program is needed to set the IP adress of iMDC-MAIN and iMDC

-RIM board. Refer to the STARTWATCH ENTERPRISE manual for the detailed installing meth

od. The content below to set IP adress of iMDC-MAIN and iMDC-RIM board would be descri

Содержание iMDC-MAIN
















































































Результаты поиска

Содержание iMDC-MAIN

Отзывы:

Похожие инструкции для iMDC-MAIN

Бренды по названию

Популярные бренды

IDTECK iMDC-MAIN, Руководство пользователя

Результаты поиска

Содержание iMDC-MAIN

Отзывы:

Похожие инструкции для iMDC-MAIN

Бренды по названию

Популярные бренды