General specifications
98
General specifications:
Frequency response: +0 / - 0.4dB, 10-20000Hz (Bypass
mode).
System distortion: < 0.01% THD, de-emphasised
Signal to Noise: 92 dB unweighted, 20 Hz - 20 kHz
I/O Delay: ~3 milliseconds
Internal sample rate: 96 kHz
Internal resolution: 40 bit floating point
I/O resolution: 24 bit
Maximum Overshoot: 0.1 dB
Phase Response: Linear 20 Hz - 20 kHz
Process Architecture: Wide band AGC / Final limiter APC®
overdrived DSP: 4 Sharc 21065, Maximum number of
Factory Presets: 10
Maximum number of User Presets: 10
Remote contact closure: 8 inputs and 12 outputs
Analogue Audio Input:
Configuration: Stereo
Impedance: > 6 kOhms
Type: Electronically balanced
Maximum Input Level: +25 dBu, for THD + N < 0.01%
Equivalent Input Noise: < - 84 dBu
Common Mode Rejection Ratio: 90 dB
Connector: Two XLR female
AD Conversion: 24 bit 128X oversampled
Digital Audio Input:
Configuration: Stereo per AES/EBU (AES3), 16, 18, 20 or
24 bit resolution.
Impedance: 110 ohms
Sampling Rate: 32, 44.1, 48, 96 kHz autodetect
Status bits: Input channel status is decoded for control.
Input User bits are optionally passed through the output
Connector: XLR female, EMI-suppressed
Filtering: RFI filtered. Effective 0.5-1000MHz
Digital Audio Output:
Configuration: Stereo per AES/EBU (AES3), 20 or 24 bits
resolution.
Impedance: 110 ohms
Sampling Rate: Software selectable, free running at 32
kHz +/- 10 PPM, 44.1 kHz +/- 10 PPM, 48 kHz +/- 10
PPM, 96 kHz +/- 10 PPM.
Synchronisation mode: Internal free running or external
or delivery mode for 32, 44.1, 48, 96 kHz
Word Length: Selectable 18, 20, 24 bits.
Jitter: Less than 5 ns rms.
Status bits: Output channel status can be generated.
Input User bits are optionally passed through the output
Connector: XLR female, EMI-suppressed
Filtering: RFI filtered. Effective 0.5-1000MHz
Digital Sync Input / Output:
Configuration: Two mode, input to provide sync, Output
to deliver sync
Impedance: 75 ohms
Sampling Rate for Input mode : 32, 44.1, 48, 96khz
Sampling Rate for Output mode : Software selectable ,
32kHz +/- 10 PPM, 44.1kHz +/- 10 PPM, 48kHz +/- 10
PPM, 96kHz +/- 10 PPM.
Connector: BNC female,
IDT – SOUND PROCESSING CORPORATION – TECHNOPARC – 5 Allée Moulin Berger – 69130 ECULLY – France
Tel +33/(0) 472.18.19.20 - Fax +33/(0) 472.18.19.21 - Web www.idt-fr.com – e-mail : [email protected]
Digital Stereo Generator:
Frequency Response: +/- 0.1 dB 20Hz - 15 kHz
Configuration: Two independently controlled output
TX1: Multiplex signal
TX2: Programmable (multiplex or 19 kHz)
Source impedance: 75 ohms
Load Impedance: 75 ohms or greater
Level: Adjustable max 15 Vpp (100% modulation ~ -3
dBFS) Connector: BNC
Pre-emphasis: 50 or 75
μ
s
Stereo separation: More than 90dB, 20Hz - 15 kHz Main
to Sub crosstalk, Sub to Main crosstalk : < -85 dB
Audio Filtering: 80 dB rejection at 19 kHz
Pilot stability: +/- 0,2 Hz
RDS / RDBS: (optional)
Basic RDS/RDBS: PI, PS, AF, PTY, RT, RTC
Dynamic RDS/RDBS: via port data UECP (Universal
Encoder
Communication Protocol)
Data port: RS232 manual selection baud rate 9600 to
115200
Remote computer interface:
Configuration : Two RS 232
Connector : One Sub-D 9 pin female and one Sub-D 9 pin
male on the back side and one Sub-D 9 pin female on
the front panel
Baud rate : Auto selectable baud rate 9600 to 115200
bauds
Remote control
Configuration: Fully remote controllable by external
modem or with the TCP/IP (optional)
Rate: 9600 to 115200 baud
Local Switch GPI/O:
Configuration: 8 inputs and 12 outputs software
controllable
Power:
Voltage: 80 to 265 VAC, 50 - 60 Hz, 130 VA
Connector: IEC, EMI-suppressed
Safety Standard: CE / DBT
Environmental and Dimensions:
Operating Temperature: 0° to 50° C or 32° to 122° F
Humidity: 0 to 95% RH, non condensing
Size: 19'', One rack unit high.
Weight: 6 Kg - 13.2 lb.
IDT Sound Processing Corporation reserves the right to make changes without previous notification. Illustrations,
descriptions and characteristics are not contractually binding and not engage the responsibility of the manufacturer.
Содержание Digital Encoder Plus
