IDT 89HPES48T12G2 Скачать руководство пользователя страница 241 | Manualshive

Страница: 241 / 276

background image

IDT PCI to PCI Bridge and Proprietary Port Specific Registers

PES48T12G2 User Manual

15 - 67

April 5, 2013

PHYLCFG0 - Phy Link Configuration 0 (0x530)

PHYLSTATE0 - Phy Link State 0 (0x540)

Bit

Field

Field

Name

Type

Default

Value

Description

7:0

Reserved

RO

0x0

Reserved field.

8

G1CME

RW

0x0

SWSticky

Gen1 Compatibility Mode Enable.

When this bit is set, the PHY

operates in Gen1 Compatibility mode. In this mode, the PHY does
not set training set bits not defined in the PCIe 1.1 specification.

10:9

Reserved

RO

0x0

Reserved field.

11

CLINKDIS

RW

0x0

SWSticky

Disable Crosslink.

When this bit is set, crosslink link training is

disabled and the device link trains as though crosslink were not
implemented.
Please refer to section Crosslink on page 6-15 for further details.

13:12

Reserved

RO

0x0

Reserved field.

14

ILSCC

RW

Downstream:

0x0

Other:

0x1

SWSticky

Initial Link Speed Change Control

. This field determines whether

a port automatically initiates a speed change to Gen2 speed, if
Gen2 speed is permissible, after initial entry to L0 from Detect.
0x0 - (automatic) Automatically initiate speed change to Gen2

speed, if permissible, after the first entry to L0 from Detect.

0x1 - (nochange) Do not automatically initiate a speed change to

Gen2 speed, stay in Gen1 speed.

Note that the initial value of this field depends on the port operating
mode.

31:15

Reserved

RO

0x0

Reserved field.

Bit

Field

Field

Name

Type

Default

Value

Description

30:0

Reserved

RO

0x0

Reserved field.

31

FLRET

RW

0x0

Full Link Retrain.

Writing a one to this field initiates full link retrain-

ing by directing the PHY LTSSM into the DETECT state. This bit
always returns zero when read.
Writing of a one to this bit always results in the switch returning a
completion to the requester before the action specified by this bit
takes effect.
For an upstream port, writing of a one to this bit always results in
the action specified by this bit to take effect after 1ms. The switch
always returns a completion to the requester before the effect of
this bit is applied.

«
...
239
240
241
242
243
...
»

Содержание 89HPES48T12G2





















































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 89HPES48T12G2

Бренд: Omega Engineering Страницы: 3

Бренд: G&D Страницы: 36

Бренд: Perel Страницы: 4

AW-FGT-100C-120

Бренд: Vivotek Страницы: 2

Бренд: Hanwell Страницы: 109

Бренд: Olympia Страницы: 6

tekmarNet4 User Switch 480

Бренд: Tekmar Страницы: 8

Бренд: Zamel Страницы: 4

Бренд: e+p Страницы: 2

EXT-UHDA-HBTL-RX

Бренд: Gefen Страницы: 33

Бренд: QSFPTEK Страницы: 12

Бренд: AMAV Страницы: 8

Бренд: N-Tron Страницы: 157

Бренд: ALFAtron Страницы: 44

Бренд: Black Box Страницы: 20

Бренд: Synergy Global Technology Страницы: 9

Бренд: ATEN Страницы: 9

BZ-UHD-88M100-ARC

Бренд: BZB Gear Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды