manualshive.com logo in svg

IDT 89HPES48T12G2, Руководство пользователя, Страница: 203 / 276

Поделиться
Скачать
IDT 89HPES48T12G2 Скачать руководство пользователя страница 203

IDT   PCI to PCI Bridge and Proprietary Port Specific Registers

PES48T12G2 User Manual

15 - 29

April 5, 2013

Message Signaled Interrupt Capability Structure

MSICAP - Message Signaled Interrupt Capability and Control (0x0D0)

8

PMEE

RW

0x0

Sticky

PME Enable.

 When this bit is set, PME message generation is 

enabled for the port.
If a hot plug wake-up event is desired when exiting the D3

cold

 

state, then this bit should be set during serial EEPROM initializa-
tion.
A hot reset does not result in modification of this field.

12:9

DSEL

RO

0x0

Data Select. 

The optional data register is not implemented.

14:13

DSCALE

RO

0x0

Data Scale

. The optional data register is not implemented.

15

PMES

RW1C

0x0

Sticky

PME Status.

 This bit is set if a PME is generated by the port even 

if the PMEE bit is cleared. This bit is not set when the P2P bridge 
within the switch is propagating a PME message but the port is not 
itself generating a PME.
Since the upstream port never generates a PME, this bit will never 
be set in that port.

21:16

Reserved

RO

0x0

Reserved field.

22

B2B3

RO

0x0

B2/B3 Support.

 Does not apply to PCI Express. 

23

BPCCE

RO

0x0

Bus Power/Clock Control Enable.

 Does not apply to PCI 

Express.

31:24

DATA

RO

0x0

Data.

 This optional field is not implemented.

Bit 

Field

Field

Name

Type

Default

Value

Description

7:0

CAPID

RO

0x5

Capability ID.

 The value of 0x5 identifies this capability as a MSI 

capability structure.

15:8

NXTPTR

RWL

Refer to sec-

tion Capabil-

ity Structures 

on page 14-3.

Next Pointer.

 This field contains a pointer to the next capability 

structure. This field is set to 0x0 indicating that it is the last capabil-
ity.

16

EN

RW

0x0

Enable.

 This bit enables MSI.

0x0 - (disable) disabled
0x1 - (enable) enabled

19:17

MMC

RO

0x0

Multiple Message Capable.

 This field contains the number of 

requested messages.

22:20

MME

RW

0x0

Multiple Message Enable.

 Hardwired to one message.

23

A64

RO

0x1

64-bit Address Capable.

 The P2P bridges within the switch are 

capable of generating messages using a 64-bit address.

31:24

Reserved

RO

0x0

Reserved field.

Bit 

Field

Field

Name

Type

Default

Value

Description

Содержание 89HPES48T12G2





















































































































































































































































































Отзывы:

Нет отзывов