manualshive.com logo in svg

idronaut Ocean Seven 304Plus, Руководство оператора

Поделиться
Скачать
idronaut Ocean Seven 304Plus Скачать руководство пользователя страница 54

SECTION SIX - BATTERIES

  

IDRONAUT 

–

 Brugherio (MB)                         

OCEAN SEVEN 304

Plus

 CTD 

12-2015 

46 

6.

 

INTERNAL BATTERIES 

The  OCEAN  SEVEN  304

Plus

  CTD  housing  has  in  its  upper  part  enough  space  to  accommodate  an 

internal battery pack. The OS304

Plus

 is powered by a single 3.6V battery; different types of battery can 

be installed in the CTD housing.  
 

 

2 x size 

“AA”

 Alkaline 1.5V battery assembled in  single battery pack    

3.0V 

 

1 x size "AA"  Lithium non rechargeable battery    

 

 

 

 

 

 

3.6V, 2.4Ah 

 

1 x size “C” 

   Lithium non rechargeable battery    

 

 

 

 

 

 

3.6V, 8.4Ah 

 

1 x size “D” Lithium non rechargeable battery

  

 

 

 

 

 

 

 

3.6V, 19Ah 

 

NiMh rechargeable IDRONAUT custom battery pack (3x1.2 AA)   

 

3.6V,2.6 Ah 

 

When  the  CTD  is  not  used  for  long  periods  (e.g.  2  weeks  or  more),  we  suggest  disconnecting  the 
internal battery pack connector from the CTD electronics or removing the internal battery pack from 
the CTD to prevent the internal batteries from damaging the CTD due to battery acid leakage. This is 
why the OCEAN SEVEN 304

Plus

 CTD is shipped without batteries installed.  

 

INSTALLING  TWO  3.6V  LITHIUM  BATTERIES  IN  THE  DOUBLE  BATTERY  HOLDER  AND 
CONNECTING  IT  TO  THE  OS304

Plus

  TOP  COVER  WILL  CAUSE  A  PERMANENT  DAMAGE 

OF THE OS304

Plus

 CTD ELECTRONICS. 

 

Optional USB Laboratory cable 

The status of the internal battery pack can be derived from the  battery diagnostic reading of the CTD 
start-up  message.  This  last  is  carried  out  only  when  the  USB  laboratory  cable  is  not  connected.  
Therefore,  to  update  the  battery  status  after  the  recharging,  switch  on  the  CTD  without  the  USB 
laboratory cable connected. 
 

6.1.

 

AISI316L & TITANIUM HOUSING BATTERY REPLACEMENT PROCEDURE 

 

Dry the CTD and lay it down on a table. 

 

Loosen  the  two  closing  screws  on  the  CTD  cover  with  a 
proper screwdriver. 

 

When  extracting  the  cover,  dry  it  and  pay  attention  to  any 
drop of water present on the cover or in the upper part of the 
CTD  body. Anyhow, dry  any trace of water in proximity of 
the external side of the o-ring.

 

 

 

Extract the plastic battery holder from the CTD housing. 

 

Replace the battery. 

 

Re-insert the plastic battery holder in the CTD housing. 

 

Gently push the wires and connectors to the side of the 
battery holder.

 

 

Gently reassemble the CTD top cover. Close the CTD with 
the two closing screws and gradually tighten them in 
sequence such as to close the cover uniformly.

 

 

Содержание Ocean Seven 304Plus
















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды