IDK MSD-702UHD Скачать руководство пользователя страница 81

Страница: 81 / 150

MSD-701UHD / 702UHD / 801UHD/ 802UHD User’s Guide

9.9.10 Multi channel audio output priority

Menu Top

→

AUDIO

→

OUT AUDIO PRIORITY

Setting for Each output channel (Common to OUTA / OUTB)

Setting value DOWN MIX, MULTI [Default]

If outputting multi channel linear PCM to a sink device, the MSD checks whether the sink device supports

multi channel linear PCM. If the sink device supports multi channel linear PCM, the MSD outputs audio with

the format. If the sink device does not support the format, the MSD outputs audio according to the setting of

“

9.9.9 Multi channel audio output

”.

You can set the priority as shown below for if some sink devices that are connected to OUTA or OUTB

support multi linear PCM while others do not.

[Table 9.12] Audio output

Setting value

Multi channel linear PCM audio

Output audio

OUTA sink device

OUTB sink device

DOWN MIX

Not supported

DOWN MIX

Supported

Not supported

DOWN MIX

Not supported

Supported

DOWN MIX

MULTI [Default]

Not supported

DOWN MIX

Supported

Not supported

MULTI

Not supported

Supported

MULTI

If no sink device is connected, it is treated as a sink device that does not support multi channel linear PCM.

Содержание MSD-702UHD























































































































































Результаты поиска

Содержание MSD-702UHD

Отзывы:

Бренды по названию

Популярные бренды

IDK MSD-702UHD, Руководство пользователя

Результаты поиска

Содержание MSD-702UHD

Отзывы:

Бренды по названию

Популярные бренды