IDK IMP-400UHD Скачать руководство пользователя

Страница: 20 / 99

IMP-400UHD User Guide

6.3.2 Connecting audio cables

Connect the audio cable to the 5-pin terminal block, and then insert the 5-pin terminal block into the

appropriate port on the IMP’s rear panel.

The IMP supports both balanced and unbalanced analog signals.

AWG28 to AWG16 conductor gauge is recommended for optimal performance.

The recommended wire strip length is 0.28 in. (7 mm).

Lch +

Lch -
GND

Rch +

Rch -

Up to 0.28 in. (7 mm)

Balanced signal

Unbalanced signal

Lch

GND

Rch

Up to 0.28 in. (7 mm)

[Fig. 6.2] Connecting audio cable to 5-pin terminal block connector

Notes:

・

The output level of balance signal connection is twice as much as that of unbalanced signal connection.

・

When input level of digital audio is 0 dBFS, output levels of analog audio unbalanced and balanced signals

are 10 dBu and 16 dBu, respectively.

6.3.3 Connecting RS-232C cable

Insert and secure the wires from the RS-232C cable into the supplied 3-pin terminal block, and then insert the

terminal block into the mating connector on the IMP.

AWG28 to AWG16 conductor gauge is recommended. The recommended wire strip length is 0.28 in. (7 mm).

Short RTS/CTS and DTR/DSR as needed.

GND

Up to 0.28" (7 mm)

Control device

GND

IMP

RxD

TxD

GND

Signal name

(Receive Data)

(Transmit Data)

(Ground)

[Fig. 6.3] Connecting RS-232C cable into 3-pin terminal block

Содержание IMP-400UHD




































































































Результаты поиска

Содержание IMP-400UHD

Отзывы:

Похожие инструкции для IMP-400UHD

Бренды по названию

Популярные бренды

IDK IMP-400UHD, Руководство пользователя

Результаты поиска

Содержание IMP-400UHD

Отзывы:

Похожие инструкции для IMP-400UHD

Бренды по названию

Популярные бренды