Idis DR-6532P-A Скачать руководство пользователя

Страница: 113 / 139

Part 2 - Configuration

113

VA Box

This screen displays an overview of VA Box events.
When an event occurs, the corresponding channel
flashes for 5 seconds.

Event Types

Exceed Occupancy
Limit

Social Distancing
Violation

Mask Rule Violation

VA Loss

Queue Congestion

System

This screen displays an overview of system events.
When an event occurs, the corresponding channel
flashes for 5 seconds.

●

Panic Record

: Displays event status based on current

Panic Record status.

●

Check Recording

: Displays event status based on

System Monitoring

settings.

●

Disk Almost Full

Disk Full

: If the storage device is

not in

Recycle

status, event status is displayed when

the amount of disk space specified under

System

Monitoring

is reached and when the disk becomes

100% full.

●

Disk Partially Almost Full / Disk Partially Full:

If the

storage device is not in Recycle status, event status is
displayed when a disk in one of multiple quota groups
reaches a specified capacity or disk usage reaches
a specified capacity under System - Monitoring. For
more information, refer to the

Mirror Configuration

Error on page 41

●

Fan Error

: Event is indicated when the cooling fan

cannot reach a certain RPM or fails for longer than 50
seconds.

●

Storage Disconnected

: Event status is displayed

when the storage device is abruptly disconnected.

●

Disk Config Change

: It will be highlighted when

the NVR reboots after the hard disk drive has been
replaced.

●

RAID Broken:

Event status is displayed when the

mirroring configuration is broken.

●

Degrade:

Event status is displayed when one of the

HDDs composing mirroring is in error.

●

No Storage Found:

It will be highlighted when no

recordable storage device has been found.

Содержание DR-6532P-A












































































































































Результаты поиска

Содержание DR-6532P-A

Отзывы:

Похожие инструкции для DR-6532P-A

Бренды по названию

Популярные бренды

Idis DR-6532P-A, Руководство по эксплуатации

Результаты поиска

Содержание DR-6532P-A

Отзывы:

Похожие инструкции для DR-6532P-A

Бренды по названию

Популярные бренды