background image

Part 1 - Remote Setup

16

Bandwidth Control

Regulates the camera’s network bandwidth use based 
on network traffic fluctuations.

Select 

Network Bandwidth limit

 and then specify 

the maximum bandwidth. The camera will not be able 
to use more than the specified limit in the event of 
network traffic.

It may not be possible to produce the frame rate 
specified under 

Video > Streaming

 if a network 

bandwidth limit has been set.

Security

 •

IP Filtering

: Select this option to enable IP Filtering. 

IP Filtering allows camera access from certain IP 
addresses and blocks access from others.

 -

Add

: Add new IP addresses to Allow List or Deny 

List. Select the 

Host

 option to add one IP address at 

a time. Select the 

Group

 option to define a range of 

IP addresses you wish to add.

 -

Remove/Remove All

: Remove individual or all IP 

addresses from Allow List or Deny List.

 •

SSL

: Select this option to enable SSL (Secure Sockets 

Layer). Enabling this option applies SSL protocol 
protection on data transmitted out. However, 
programs and systems that do not support SSL will 
not be able to connect to the camera. If this option 
has been changed, click 

Save

 to apply the current 

settings, and then restart Remote Setup. If you do not 
restart Remote Setup, the changes afterwards will not 
be applied.

 • Time server, FEN Server, and SMTP server's IP 

addresses must be added to Allow List under 

IP 

Filtering

 in order to use Time Sync, FEN, and Send 

Email features. No connection to the camera will be 
permitted whatsoever from IP addresses added to 

Deny List

.

 • Enabling the 

SSL

 option may place a greater load 

on the external system, depending on the level of 
security being used.

 • When using SSL 

Very High

, the maximum bit rate of 

H.265 / H.264 / JPEG is limited to 3Mbps.

 • This product contains software developed by Open 

SSL Project for use in Open SSL Toolkit. (http://www.
openssl.org/)

Содержание DC-D4236RX















































Отзывы: