IDEC SmartAXIS FT9Z-1A01 Скачать руководство пользователя страница 372

Страница: 372 / 393

PPENDIX

Appendix-2

MART

AXIS P

/ L

ITE

SER

ANUAL

FT9Y-B1378

Upgrade SmartAXIS System Software

The system software of SmartAXIS can be upgraded using WindLDR. If the system software of your SmartAXIS is old, upgrade the

system software with the following procedure:

Connect the SmartAXIS to the computer where WindLDR is installed using USB maintenance cable (recommended cable:

HG9Z-XCM42).

Note:

System software cannot be downloaded via the expansion communication ports or the Ethernet port.

From the WindLDR menu bar, select

Online

Download

System Software Download

The System Software Download dialog box appears.

Select the PLC type and the system software version to download, and then click

Start System Software Download

Notes:



If the SmartAXIS is running, it is stopped automatically before the system software download starts.



Older system software can also be downloaded to the SmartAXIS if required.



The system software download takes about one minute.

The latest version is indicated as default.

Older versions are also available.

Details of upgrades are indicated.

Содержание SmartAXIS FT9Z-1A01










































































































































































































































































































































































































Результаты поиска

Содержание SmartAXIS FT9Z-1A01

Отзывы:

Похожие инструкции для SmartAXIS FT9Z-1A01

Бренды по названию

Популярные бренды

IDEC SmartAXIS FT9Z-1A01, Руководство пользователя

Результаты поиска

Содержание SmartAXIS FT9Z-1A01

Отзывы:

Похожие инструкции для SmartAXIS FT9Z-1A01

Бренды по названию

Популярные бренды