Ideal Vacuum Habanero P1012726 Скачать руководство пользователя

Страница: 17 / 19

[email protected]

www.idealvac.com

HRCF-08122022 - V 1.1

11. Press the power switch to turn on the controller.
12.

The first time the controller is powered and connected to the furnace, the current temperature

(PV) will be ambient. The target temperature (SV) will be 0.0 (Figure 17).

13. The PV (process value) is the furnace’s current temperature, shown in red digits. The SV is

the furnace target temperature, shown in green digits.

14. The controller is factory programmed to turn the furnace on immediately upon power up.
15. To turn off furnace heating and enter a new furnace target temperature, press the

ROTATE

button. The display will show “

r-S

” and

RUN

(Figure 18, next page).

16. Press the

UP ARROW

. The display changes to

STOP

(Figure 19, next page).

17. Press the

SET

Button to save the selection and go back to the temperature display.

18. Similarly, if

r-S

is set to

STOP

, press the

ROTATE

button. Press the

UP ARROW

to change

RUN

. Press the

SET

Button to save the selection and go back to the temperature display.

Figure 16 - Plug furnace power and thermocouple cables into controller

Figure 17 - Initial current and target temperatures

Содержание Habanero P1012726




















Результаты поиска

Содержание Habanero P1012726

Отзывы:

Похожие инструкции для Habanero P1012726

Бренды по названию

Популярные бренды

Ideal Vacuum Habanero P1012726, Руководство пользователя

Результаты поиска

Содержание Habanero P1012726

Отзывы:

Похожие инструкции для Habanero P1012726

Бренды по названию

Популярные бренды