SK617
www.idealinc.com
PORTABLE MOTION SENSOR ALARM
4 ZONE EXPANDABLE SYSTEM
This is an all in one portable Motion Sensor with a built in Alarm or Chime that
can be expanded to create a simple 4 zone security system.
Ideal for hotel rooms, apartments, and offices where an easy to setup security
system is required. Expandable, a total of 8 IDEAL SECURITY INC wireless devices
(sensors & remotes) can be linked to the motion sensor to easily establish a wider,
multipurpose protected area.
Once installed, the system will sound an alarm or chime if your security perimeter
is broken. It can be armed and disarmed with the included remote control
DESCRIPTION OF COMPONENTS
1. AC/Battery low indicator LED
2. ALARM/CHIME working mode LED
3. PIR sensor
4. Buzzer
5. Zone indicator LED’s
6. Alarm/Off/Chime switch
FEATURES
• Motion Sensor, detects motion & activates built in 105db alarm or door chime.
• Detects motion in a 100° arc with a range of up to 7 meters (23’).
• Portable travel friendly design. Easily set up a security zone anywhere.
• Remote Control included
• Expandable 4 Zone wireless receiver:
Add up to 8 wireless sensors or remote controls.
- Zones 1, 2 & 3 can link with one additional wireless sensor each.
- Zone 4 can link with up to 5 Remote Controls or Wireless Sensors.
• Wired expandability:
- Input terminal compatible with wired magnetic contact sensors.
- Siren terminal compatible with wired outdoor sirens.
• Alarm/OFF /Chime switch
• AC/Battery low indicator, Armed mode indicator & Zone trigger LED’s
• AC adaptor operation (included) with 3 AAA size backup batteries
• Wall mount swivel bracket kit
SET UP AND INSTALLATION
1. Remove the screw from the battery compartment cover of the main unit, install
the included 3“AAA” size back-up batteries, make sure to install with correct
polarity. The batteries will keep the unit working for a limited time in case of
power failure. (fig.1)
2. Check the Motion Sensor (PIR) ON/OFF switch (fig.2)
ON: Enable buit-in motion sensor OFF: Disable built-in motion sensor
3. Position the motion detector:
The motion detector may be used as a portable unit by placing on any suitable flat
surface or it may be mounted in a more permanent manner using the swivel mount
provided. For best coverage choose a suitable location, 5 - 6 feet (1.5 - 2.0 meters)
above floor level. (Fig.3)
To mount permanently choose a suitable location near an electrical outlet. Use the
swivel wall mount bracket template provided to mark the proper location. Drill
holes, install anchors and attach the bracket
with the screws provided. Place the main unit
into the bracket and slide it down to secure
in place. Adjust the bracket to obtain the best
coverage of the area to be protected.(Fig 4)
4. Plug the AC adaptor into the adaptor jack
located on the side of the unit and into
a 110V household outlet. (Fig. 5)
PREPARE THE REMOTE CONTROL
1. Remove the battery compartment cover
by sliding it in the direction of the arrow.
2. Insert the CR2032 Coin Cell battery.
Make sure the polarity (+ or -) of the
batteries match the polarity marks inside
the unit. As shown in (Fig.6)
3. Replace battery cover
TO ARM THE UNIT
1. Slide the switch to "ALARM", your will hear 3 short beeps and the MODE
indication LED will flash once every 3 seconds to confirm it is Armed.
2. Pressing the "ARM" button on the remote control will also Arm the main unit.
3. After arming the unit There will be a 60 second exit delay followed by a
"BEEP". The system will be active after that "BEEP".
NOTE: When using the remote control make sure the switch on the main unit
is set to either "ALARM" or "CHIME".
ENTRY DELAY AND LED TRIGGER INDICATORS
In "ALARM" mode, if motion is detected or a linked wireless sensor is triggered
there will be a 5 second entry delay before the alarm is activated. The 105dB
alarm will sound for 30 seconds for 2 cycles with 30 seconds silence in between.
NOTE:
1. When the built-in motion sensor is triggered the "MODE" indicator LED will flash.
2. When a linked wireless sensor is triggered the corresponding wireless zone
indicator LED (1 ~ 4) will flash.
3. Once an alarm has been triggered if the system is not turned off or disarmed
the system will automatically return to Arm mode. The system will be ready to
receive new trigger signals.
TO DISARM OR TURN OFF THE UNIT
1. Slide the switch to "OFF" to turn the Alarm functions off. The system will not
respond to the Remote Control while the switch is set to "OFF".
2. Pressing the "DISARM" button on the remote control unit will stop the main
unit from sounding an alarm. You will hear a long beep to confirm the main
unit has been disarmed.
NOTE: If the system was triggered, you will hear 5 seconds of beeps after
pressing the disarm button
7. DC 9V power jack
8. LEARN button
9. Battery compartment
10. PIR ON/OFF switch
11. External terminal
12. Battery cover
ALARM
OFF
CHIME
2
3
6
1
7
9
10
11
12
8
5
4
(fig.1)
(fig.2)
TRIG GND GND SIREN
PIR ON OFF
100
o
3-6m (10’-20’)
1.5-2.0m
(5’-6’)
(Fig.4)
(Fig.3)
(Fig. 5)
(Fig.6)
CHIME OR HOME FUNCTION
1. Slide the switch to "CHIME" or Press "HOME" button on the remote control.
You will hear Ding..Dong sound and the "MODE" indication LED will light up
to confirm that the unit is in Chime mode.
2. Wait for 60 seconds after a beep for the sensor to Arm.
When the built-in motion sensor detects movement the unit will sound "Ding
Dong" and the "MODE" indicator LED will flash at the same time.
When a linked wireless sensor triggers the unit, it will sound "Ding Dong" and
the corresponding wireless zone indicator LED will flash at the same time.
3. Slide the switch to "OFF" or press the "DISARM" button on the remote control
to turn the chime function off .
NOTE: The function switch must be set to either "ALARM" or "CHIME" for the
remote control to activate Alarm, Chime (Home), Disarm or Panic
PANIC BUTTON
1. With the function switch on the main unit set to either "ALARM" or "CHIME",
press and hold the "PANIC" button on the remote control for 2 seconds. The
105 dB alarm will be instantly activated and "ZONE 4" indicator LED will flash.
The alarm will sound twice for 30 seconds with 30 seconds silence in between.
2. To stop the alarm slide the function switch on the main unit to "OFF" or press
the "DISARM" button on the remote control.
LINKING ADDITIONAL WIRELESS DEVICES
1. Turn the unit to Chime mode by sliding the switch on the right side to “CHIME”.
2. Turn off the integrated motion sensor by sliding the “PIR” switch in the
battery compartment to the OFF position.
Please remember to slide it to the ON position once the linking process is done.
3. Press and hold the “LEARN” button located on the back of the unit for 2
seconds until you hear a long beep tone, release the button.
4. The zone 1 LED will flash, a short press of the LEARN button will change to
zone 2, a short press again and the zone 3 LED will flash, and so on.
If a zone LED is steady on, that means the zone is full. Zones 1, 2 &3 can
accept 1 wireless device each. Zone 4 can accept up to 5 wireless devices.
5. Once the zone # is chosen, trigger the wireless device that you want to link to
the system (Please refer to its instructions for how to trigger the sensor). If
you hear two long beeps, then the linking process is successful. Otherwise,
please re-learn again. The system will go back to standby mode for each code
learning process. Repeat step 2 to 4 to learn other devices.
7. Slide the integrated motion detector PIR switch back to ON position.
TO REMOVE WIRELESS DEVICES
1. Switch the unit to “CHIME” mode.
2. Press the LEARN button for 2 seconds. You will hear a long beep then release
the button. To select the zone that you want to clear press the button briefly to
cycle through the zones. The zone LED will flash. Press and hold the button for
12 seconds until you hear 2 long beeps then release the button. Now the link
code is cleared from the zone you selected.
3. Repeat if necessary for other zones.
ADDING WIRED CONTACT SENSORS
When mounted permanently the unit is compatible with IDEAL wired magnetic
contact sensors SK619. When connected the sensors will activate the alarm in the
same manner as the built in motion sensor.
1. Mount the contact sensors as described in the instructions for the SK619.
Measure and cut the sensor wires to the length needed to reach the unit plus
about 3 inches of extra wire. Strip about 1/2 inch of insulation from each wire.
2. Open the rear cover of the unit to access the input terminals.
3. Feed the two wires through one of the slots on the side of the unit. Using a
small screwdriver connect one wire to the terminal marked “TRIGGER” and the
other wire to the terminal just beside it marked “GRND”. Either wire can be
mounted to either terminal. (Fig.8)
4. Close the back cover. The unit is now ready to be armed
ADDING A WIRED EXTERNAL SIREN
When mounted permanently the unit is compatible with IDEAL wired exterior
siren SK613. When connected the external alarm will sound when the main unit is
triggered and the function switch is set to “ALARM”. The Siren will not sound when
the function switch is set to “CHIME” or “HOME” is selected with the
Remote Control
1. Mount the Siren as described in the instructions for the SK613. Measure and
cut the sensor wires to the length needed to reach the unit plus about 3 inches
of extra wire. Strip about 1/2 inch of insulation from each wire.
2. Open the rear cover of the unit to access the input terminals.
3. Feed the two wires through one of the slots on the side of the unit. Using a
small screwdriver connect the black striped wire (-) to the terminal marked
“GRND” and the other wire (+) to the terminal just beside it marked “SIREN”.
The polarity of the wires must be respected for the Siren to function. (Fig.9)
4. Close the back cover. The unit is now ready to be armed
IMPORTANT NOTES:
1. Do not install alarm where it will be exposed to direct sunlight or rain.
2. The alarm siren is very loud, never put the unit close to your ear.
3. Keep away from heat sources such as radiators, heat ducts or stoves.
4. If the unit goes off at random, it is possibly located too close to a heat source.
Changing the location or direction of the unit can remedy this.
5. The unit is designed to be used with the built in AC adapter plugged into a
110V outlet. Batteries will provide short term back-up functionality.
6. It is recommended that batteries be replaced annually - like smoke detector
batteries.
7. For the most up to date installation instructions and trouble shooting
information consult our web site: www.idealinc.com
8. The system can provide valuable protection for your home and property if
utilized properly. However, this unit cannot guarantee complete protection
against burglary or robbery. Therefore, we can not be responsible for any
losses or damages which may occur.
WARRANTY:
This unit is warranted to be free of defective materials and workmanship for a
period of one year from date of purchase. In case of malfunction, this unit will be
repaired or replaced at no charge by Ideal Security Inc. Return the product
postage paid, along with your sales slip to Ideal Security Inc., 7111 Cordner
Street, Lasalle, Quebec, Canada, H8N 2J7. Warranty begins on date of consumer
purchase. Repair or replacement as described above shall be the sole remedy to
the consumer and there shall be no liability on the part of Ideal Security Inc. for
any special, indirect, incidental or consequential damages, including but not
limited to any loss of business or profits whether or not foreseeable.
CUSTOMER SERVICE:
Thank you for your purchase:
We are dedicated to customer service and will work to resolve any difficulties to
ensure customer satisfaction.
If you have any questions about the setup or function of this product, please call
us before returning this product to the point of purchase.
Tel: 800-361-2236 x 230 • Fax: 800-361-3423
e-mail: [email protected]
www.idealinc.com • www.idealalert.ca
