manualshive.com logo in svg

ICT PRT-PSU-DIN-4A, Руководство по установке, Страница: 14 / 49

Поделиться
Скачать
ICT PRT-PSU-DIN-4A Скачать руководство пользователя страница 14

Mains Power

The power supply should be supplied by a dedicated electrical power source rated for a minimum 5 amp load
and have a dedicated circuit breaker.

Connect the power supply module to mains input via an appropriate IEC-C7 90 degree cable.

L

N

Mains Input

The earth wire shall be routed to the V- terminal on the power supply.

Warning:

⦁

This installation should be made by qualified service personnel and should conform to all local codes.

⦁

Termination of wiring to the power supply while power is applied or the battery is connected may cause
serious damage to the power supply and will

VOID ALL WARRANTIES OR GUARANTEES

. Power the unit

only after all wiring, configuration and jumper settings are completed.

⦁

Extra care must be taken when wiring the AC inputs. Improper connection will cause permanent damage
to the power supply.

PRT-PSU-DIN-4A | Protege DIN Rail 4A Intelligent Power Supply | Installation Manual

14

Содержание PRT-PSU-DIN-4A


















































Отзывы:

Нет отзывов