manualshive.com logo in svg

ICT PRT-MNR2-DIN, Руководство по установке

Поделиться
Скачать
ICT PRT-MNR2-DIN Скачать руководство пользователя страница 20

LED Indicators

Protege DIN rail modules feature comprehensive diagnostic indicators that can aid the installer in diagnosing faults
and conditions. In some cases an indicator may have multiple meanings depending on the status indicator display
at the time.

Power Indicator

The power indicator is lit when the correct input voltage is applied to the module.

Note that this indicator may take several seconds to light up after power has been applied.

State

Description

On (green)

Correct input voltage applied

Off

Incorrect input voltage applied

Status Indicator

The status indicator displays the status of the module.

State

Description

Continuous slow flash (green)

Module is operating normally

Constantly on (green)

Module is powering up

Fault Indicator

The fault indicator is lit any time the module is operating in a non-standard mode.

State

Description

Continuous slow (red) flash

Module is in boot mode awaiting firmware update

Ethernet Indicator

The ethernet indicator will show the status of the ethernet connection.

State

Description

Constantly on (green)

'Live' ethernet connection detected

Constantly off

No ethernet connection detected

Continuous (green) fast flash

Ethernet packet transmitted/received

PRT-MNR2-DIN | Protege Module Network Repeater | Installation Manual

20

Содержание PRT-MNR2-DIN
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды