ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 97

ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 64

Hybrid Ultra

855-350-050_Rev2.0_Instruction Manual

Page

52

of 84

Table 28. Deeply discharged battery values (typical)

24 VDC Units

48 VDC Units

20 VDC

40 VDC

Battery Over-Current Alarm

Over-Current Threshold:

Set the threshold to receive an alarm

notification when the battery discharge or charge current exceeds a set
overcurrent level. Set the threshold to 0 amps to disable this alarm. The
default setting is 0 (Disabled).

Battery Low SOC Alarm

SOC Threshold

: Set this to receive an alarm notification when the

battery state of charge falls below the specified level. Set the threshold
to 0 amps to disable this alarm. This setting is only available if the system
is configured for use with a lead-acid type battery. The default setting is
0 (Disabled).

Alarm Reporting

Ignore Circuit Breaker 2 Status

: Select the check box to prevent alarm

e-mails being sent when a single battery is connected to a BMMD. This
setting is only available if a BMMD is installed. The default setting is
Disabled.

Activate Alarm Form C Contact:

Select the check box to have the rear

panel alarm contacts change state for an alarm condition. The default
setting is Enabled.

«
...
62
63
64
65
66
...
»

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов