ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 97

ICT Hybrid Ultra ICT-2U4-DC12 Скачать руководство пользователя страница 63

Hybrid Ultra

855-350-050_Rev2.0_Instruction Manual

Page

51

of 84

voltage. The battery is reconnected when AC power is restored or after
recharging to a preset threshold.

Disconnect Voltage:

Set the threshold to a level that will protect the

battery from excessive discharge (as recommended by the battery
manufacturer). The LVD contactor will open when the battery discharges
to this level for at least 3 seconds. The default setting varies based on
the Power Modules installed.

Table 25. Default Disconnect Voltage Settings

Module

ICT700-24PM

ICT1500-24PM

ICT700-48PM

ICT1500-48PM

Threshold Voltage

21.0 VDC

42.0 VDC

Reconnect Voltage:

Set the level where the unit will reconnect to the

battery after it has recharged (as recommended by the battery
manufacturer). The "Reconnect Voltage" must be higher than the
Disconnect Voltage to prevent the LVD contactor repeatedly cycling on
and off. The default setting varies based on the Power Modules installed.

Table 26. Default Reconnect Voltage Settings

Module

ICT700-24PM

ICT1500-24PM

ICT700-48PM

ICT1500-48PM

Threshold Voltage

25.0 VDC

50.0 VDC

Table 27. The minimum difference between Disconnect and Reconnect voltages

24 VDC Units

48 VDC Units

2 V

4 V

This setting will be used when charging the battery from an external DC
source (such as a solar system), otherwise once AC power returns the
LVD contactor will automatically close so that the Power Modules can
charge the battery directly.

NOTE: Deeply discharged batteries will not be reconnected as a safety

measure. Refer to the battery manufacturer’s recommendations on
how to proceed with a deeply discharged battery.

«
...
61
62
63
64
65
...
»

Содержание Hybrid Ultra ICT-2U4-DC12


































































































Отзывы:

Нет отзывов