ICS Advent ADIO1600 Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 72

ICS Advent ADIO1600 Series Скачать руководство пользователя страница 42

Manual Number: 00650-004-5

Page 5-8

ADIO1600 Manual

Mode 0

This functional configuration provides simple input and output operations for each of the three

ports. No handshaking is required, data is simply written to or read from a specified port.

Mode 0 Basic Functional Definitions:

Two 8-bit ports and two 4-bit ports
Any port can be input or output
Outputs are latched
Inputs are not latched
16 different Input/Output combinations are possible in this mode

Mode 1

This functional configuration provides a means for transferring I/O data to or from a specified port

in conjunction with strobes or handshaking signals. In Mode 1, Port A and Port B use the lines

on Port C to generate or accept these handshaking signals.

Mode 1 Basic Functional Definitions

Two Groups (Group A and Group B)
Each group contains one 8-bit data port and one 4-bit control/data port
The 8-bit data port can be either input or output. Both inputs and outputs are latched
The 4-bit port is used for control and status of the 8-bit data port

Mode 2

This functional configuration provides a means for communicating with a peripheral device or

structure on a single 8-bit bus for both transmitting and receiving data (bi-directional bus I/O).

Handshaking signals are provided to maintain proper bus flow discipline in a similar manner to

MODE 1. Interrupt generation and enable/disable functions are also available.

Mode 2 Basic Functional Definitions

Used in Group A only
One 8-bit, bidirectional bus port (Port A) and a 5-bit control port (Port C)
Both inputs and outputs are latched
The 5-bit control port (Port C) is used for control and status for the 8-bit, bi-directional bus port

(Port A)

«
...
40
41
42
43
44
...
»

Содержание ADIO1600 Series









































































Отзывы:

Нет отзывов