ICS Advent ADIO1600 Series Скачать руководство пользователя страница 27

Страница: 27 / 72

Chapter 4: Software

Manual Number: 00650-004-5

Page 4-3

unsigned integer

MAXIRQ():
Returns a number that indicates the highest IRQ that the card can access.

(15)

unsigned integer

VALIDIRQ():
Returns a bitmask (16 bit value) with ones at valid IRQ possibilities.

STARTCONVERSION (unsigned int BASE_ADDRESS):

Causes the A/D card to begin an analog-to-digital conversion. The only

parameter is the base address of the card, and the routine does not have a

return value.

unsigned integer CHECKFOREOC (unsigned int BASE_ADDRESS):

This function returns zero (FALSE) if the card is busy performing an analog

conversion. Otherwise, it returns non-zero (TRUE). The only parameter

is the base address of the card.

unsigned integer WAITFOREOC (unsigned int BASE_ADDRESS):

This function will monitor the status of EOC (using CHECKFOREOC)

until either EOC occurs or a timeout occurs. The timeout is defined as

262,144 occurrences of the check for EOC. The actual timeout depends on

the speed of the computer in use and can be determined by measurement.

The function returns TRUE (non-zero) if it detected EOC and FALSE

(zero) if the routine timed out. (The exact number it returns is the number

of tries remaining before timeout occurs.)

unsigned integer RETRIEVEANALOGCONVERSION (unsigned int BASE_ADDRESS)

Returns a two-byte unsigned number that indicates the value of the A/D data

completed analog-to-digital conversion. This routine does

not

wait for

EOC. Therefore, if you use STARTCONVERSION followed immediately

by this routine, the data that you receive is from the

previous

conversion,

not the one just started. See

Using the Driver

, later in this section of the

manual, for more information.
Only the bits that relate to the input voltage are returned, right justified if

not a full 16 bits wide. Any extra bits returned by the A/D card are thrown

away. Use the RETRIEVEANALOGDATA function if you want the raw

bits from the A/D card.

unsigned integer RETRIEVEANALOGDATA (unsigned int BASE_ADDRESS)

Returns a two-byte unsigned number that indicates the value of the A/D data

completed analog-to-digital conversion. This routine does

not

wait for

EOC. Therefore, if you use STARTCONVERSION followed immediately

by this routine, the data that you receive is from the

previous

conversion,

not the one just started. See

Using the Driver

, later in this section of the

manual, for more information.

Содержание ADIO1600 Series









































































Результаты поиска

Содержание ADIO1600 Series

Отзывы:

ICS Advent ADIO1600 Series, Руководство по эксплуатации продукта, Страница: 27 / 72

Результаты поиска

Содержание ADIO1600 Series

Отзывы: