ICS Advent ADIO1600 Series Скачать руководство пользователя страница 26

Страница: 26 / 72

Manual Number: 00650-004-5

Page 4-2

ADIO1600 Manual

Also, to support sub-multiplexers such as the AT16-P or LVDT8-P, a second driver module known

as a Multiplexer Driver Module, or MDM, is provided with the sub-multiplexer card. Routines in

the MDM are specific to the nature of the sub-multiplexer supported, but a common functionality

is transparently supported by all MDMs. This allows the simplest application of a sub-multiplexer

(multiplexing A/D channels to provide additional channels) to be written identically regardless of

the sub-multiplexer in use.

Together, these two driver module types, CDM and MDM, provide simple and portable access to

both the A/D cards and the attached sub-multiplexers. This section of the manual gives detailed

information about the CDMs provided and the ADIO1600 CDM.

NOTE:

For most programs, no knowledge of the MDM specification is required. If the only data you

intend to acquire is from the ADIO1600, using the ADIO1600 CDM exclusively will reduce the

learning curve even further. You need to use the MDM only for the most advanced features or

for speed-critical algorithms.

Card Driver Modules (CDM)

Each Card Driver Module provides routines to access a specific A/D card type. All of the CDMs

provide the same functionality, eliminating most card-specific software design issues. These driv-

ers are provided in the form of .OBJ object files that can be linked to any language that supports the

Pascal calling convention (QuickBASIC, VisualBASIC, C, C

, Fortran, Assembler, and Pascal,

just to name a few). Each object file is named the same as the A/D card six-character part number,

making it easy to locate the driver to be used.

These CDMs allow a given application to be written for a multitude of A/D cards without chang-

ing a single line of code. To switch from one A/D to another, simply re-link the application with the

new CDMs .OBJ file. This driver system is also upgradeable and allows various expansion op-

tions to be attached to the CDM files, such as sub-multiplexer cards, statistical analysis libraries, or

dynamic load drivers. Also, the specification for the CDM is available and allows you to write

CDM files for third-party A/D cards. This greatly simplifies mixed-vendor programming support.

Card Driver Modules provide the following functions:

unsigned integer

AD_NAME():
Returns a number that represents the name of the A/D card that the specific

Card Driver Module (CDM) supports.

unsigned integer

MAXCH():

Returns a number that indicates the maximum number of channels available.

The ADIO1600 CDM returns 16.

Содержание ADIO1600 Series









































































Результаты поиска

Содержание ADIO1600 Series

Отзывы:

ICS Advent ADIO1600 Series, Руководство по эксплуатации продукта, Страница: 26 / 72

Результаты поиска

Содержание ADIO1600 Series

Отзывы: