ICS Advent ADIO1600 Series Скачать руководство пользователя страница 15

Страница: 15 / 72

Manual Number: 00650-004-5

Page 2-2

ADIO1600 Manual

Discrete Digital I/O

Four bits of TTL/CMOS-compatible digital input capability are provided at the mounting panel con-

nector. Twenty-four additional digital I/O bits are available at the auxiliary connector on the board

which are available at a backplate connector via a ribbon cable extension from the auxiliary connec-

tor. Digital inputs IP0 and IP2 have dual uses. Input IP0 provides an external trigger for the A/D.

Input IP2 is also the gate input for Counter/Timer 0. Note that the use of the Counter prevents use

of IP2.

Four bits of digital output are available with powerful LSTTL logic level load drive capability. Dis-

crete outputs OP0 through OP3 provide multiplexer addressing for input expansion card use, as

described in the

INPUT SYSTEM EXPANSION

section, or as separate digital outputs.

Additionally, OP0 through OP3 can be individually software configured for use as additional TTL/

CMOS-compatible digital inputs, providing a total of up to eight Digital Inputs at the rear panel

connector.

The auxiliary digital I/O port is from a 8255 Programmable Peripheral Interface which provides 24-

bits of bi-directional input/output bits configured as two sets of 8-bit and two sets of 4-bit digital

input/output ports. This port is extended using a ribbon cable from the side of the board to a 37-pin

connector on a rear mounting bracket.

Counter/Timer

The ADIO1600 contains a type 8254 counter/timer which has three 16-bit programmable down

counters. Counter/Timer #0 is enabled by a digital input (IP2) and uses either the internal 1MHz

clock or an external clock of up to 10 MHZ. Counter/Timers #1 and #2 are concatenated and form

a 32-bit counter/timer for timed A/D trigger pulses and/or external frequency generation. The dual

counter/timer can be enabled by program control and clocked by a 1 MHZ on-board crystal oscilla-

tor source. Counter #2 may be set to generate an interrupt request (IRQ) upon completing a

counter period.

Counter/Timer 0 and Counter/Timers 1 and 2 can be set up for event counting, frequency or period

measurements, and pulse or wave form generation. Also, Counter/Timers 1 and 2 can be pro-

grammed to initiate A/D conversions. See the

PROGRAMMABLE INTERVAL TIMER

sec-

tion of this manual for a description of ways that the type 8254 counter/timer chip can be used.

Analog Output

The ADIO1600 has two 12-bit digital-to-analog converters (D/A) connected to output drivers ca-

pable of providing 5 mA current drive. By selecting on-board jumpers outputs of 0-5 VDC, 0-10

VDC, 0-2.5 VDC, ±2.5 VDC, ±5VDC, or ±10 VDC are possible.

Interrupts

Interrupts can be initiated by completion of an A/D conversion or Counter timeout if programmed by

software. Interrupt levels 2-7, 10-12, 14 and 15 are selectable via jumpers.

Содержание ADIO1600 Series









































































Результаты поиска

Содержание ADIO1600 Series

Отзывы:

ICS Advent ADIO1600 Series, Руководство по эксплуатации продукта, Страница: 15 / 72

Результаты поиска

Содержание ADIO1600 Series

Отзывы: