ICRealtime Edge IPEG-D20F-IRW3 Скачать руководство пользователя страница 142 | Manualshive

Страница: 142 / 200

background image

Setting Video Detection

The camera will trigger an event if there are considerable pixellation changes on the video such as
moving objects or if the camera as been tampered and moved from its original position.

Setting Motion Detection

The camera will trigger an event if there is pixellation change due to movement.

●

If motion detection and Intelligent Motion detection is enabled simultaneously, with configured
linked events, the linked events will take effect as following:

◇

When

Motion Detection

is triggered, the camera will record and take snapshots, but other

configured linkages such as sending emails, PTZ operation will not take effect.

◇

When Intelligent Motion Detection is triggered, all the configured linkages take effect.

●

If you only enable motion detection, all the configured linkages take effect when motion
detection is triggered.

Step 1

Select

Setting

>

Event

>

Video Detection

>

Motion Detection

.

Figure 5-22 Motion detection

Step 2

Select the

Enable

checkbox to enable motion detection.

Step 3

Set an Regionfor motion detection.
1) Click

Setup

next to

Area

.

Figure 5-23 Area

130

«
...
140
141
142
143
144
...
»

Содержание Edge IPEG-D20F-IRW3









































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Edge IPEG-D20F-IRW3

Бренд: Samsung Страницы: 200

Бренд: Abus Страницы: 16

Бренд: Hanwha Vision Страницы: 15

Бренд: Channel Vision Страницы: 2

Бренд: Q-See Страницы: 9

STAR-LIGHT Universal HD over Coax DWC-D3263TIR

Бренд: Digital Watchdog Страницы: 36

Бренд: Alecto Страницы: 12

Бренд: Servodan Страницы: 6

Бренд: PheeNet Страницы: 5

Бренд: Observint Страницы: 20

NVIP-1DN3000H/IR-1P-II

Бренд: Novus Страницы: 32

Бренд: Dorlen Страницы: 2

Бренд: Brickcom Страницы: 19

Бренд: AVS Страницы: 2

DH-IPC-HFW1200SP-W

Бренд: Delta Страницы: 6

Бренд: OpenEye Страницы: 2

DS-2CC592 P(N)-FB

Бренд: HIKVISION Страницы: 6

IQeye R5 Series

Бренд: Vicon Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды