ICP DAS USA tM-TH8 Скачать руководство пользователя страница 38

Страница: 38 / 140

tM-TH8 User Manual, Rev: A1.1 7MH-018-A11

2.3 #AAN

Description:

Reads the analog input of channel N.

Syntax:

#AAN[CHKSUM](CR)

Delimiter character

Address of the module to be read (00 to FF)

The channel to be read, zero based.

Response:

Valid Command:

>(Data)[CHKSUM](CR)

Invalid Command:

?AA[CHKSUM](CR)

Delimiter character for a valid command

Delimiter character for an invalid command. An
invalid command is returned if the specified
channel is incorrect.

(Data)

Analog input data of the specified channel, see
Section 1.10 for the data format. For the tM-
TH8, if the specified channel is disabled, then
the data field will be filled with space characters.

Address of the responding module (00 to FF)

There will be no response if the command syntax is
incorrect, there is a communication error, or there is no
module with the specified address.

tM-TH8

Содержание tM-TH8













































































































































Результаты поиска

Содержание tM-TH8

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM-TH8, Руководство пользователя

Результаты поиска

Содержание tM-TH8

Отзывы:

Бренды по названию

Популярные бренды