manualshive.com logo in svg

ICP DAS USA tM Series, Руководство пользователя

Поделиться
Скачать
ICP DAS USA tM Series Скачать руководство пользователя страница 138

 
 

A.5 Safe Value and Power-on Value of 

Digital Output 

 
Besides setting by the set digital output commands, the digital 
outputs can be set under two other conditions. 
 
When the host watchdog is enabled and a host watchdog 
timeout occurs, the “

safe value

” is loaded into the digital 

output ports. The set digital output commands have no effect 
on the digital output ports until the host watchdog timeout 
status is cleared.  The host watchdog timeout status is saved in 
the EEPROM.  The status is not changed even after power-on 
reset.  It can be cleared only by the reset host watchdog 
timeout status command ~AA1.  See Section A.2 for host 
watchdog details.   
 
When the module is powered on and the host watchdog 
timeout status is cleared, the “

power-on value

” is loaded into 

the digital output ports.  If the host watchdog timeout status is 
not cleared on power-on, then the safe value is loaded into the 
digital output ports. 
 
Both the safe value and power-on value are set by the ~AA5V 
command.  Refer to Section 2.30 for details. 

tM Series DIO User Manual, Rev: A1.3  7PH-013-A13 

138 

ГК

 

Атлант

 

Инжиниринг

 – 

официальный

 

представитель

 

в

 

РФ

 

и

 

СНГ

 

+7(495)109-02-08 [email protected] www.bbrc.ru 

Содержание tM Series

















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды