ICP DAS USA tM Series Скачать руководство пользователя страница 114

Страница: 114 / 144

3.7 70 (0x46) Read/Write Module Settings

This function code is used to read the settings of the module or
change the settings of the module. The following sub-function codes
are supported.

Sub-function Code

Description

Section

00 (0x00)

Read the module name

3.7.1

04 (0x04)

Set the module address

3.7.2

05 (0x05)

Read the communication settings

3.7.3

06 (0x06)

Set the communication settings

3.7.4

32 (0x20)

Read the firmware version

3.7.5

33 (0x21)

Set the DI counter edge

3.7.6

34 (0x22)

Read the DI counter edge setting
value

3.7.7

39 (0x27)

Set the DO power-on value

3.7.8

40 (0x28)

Read the DO power-on value

3.7.9

41 (0x29)

Set the DI/O active states

3.7.10

42 (0x2A)

Read the DI/O active states

3.7.11

If the module does not support the sub-function code specified in the
message, then it responds as follows:

Error Response

Address

1 Byte

1 ~ 247

Function code

1 Byte

0xC6

Exception code

1 Byte

Refer to the Modbus standard for
more details.

tM Series DIO User Manual, Rev: A1.3 7PH-013-A13

114

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание tM Series

















































































































































Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды

ICP DAS USA tM Series, Руководство пользователя

Результаты поиска

Содержание tM Series

Отзывы:

Бренды по названию

Популярные бренды