ICP DAS USA MDC-211-ZT Скачать руководство пользователя страница 7

Страница: 7 / 46

ICP DAS, MDC-211-ZT user manual , v1.0 Page 6

1.3.

Specifications

MDC-211-ZT
Radio Standard

RF Channel

Antenna (2.4 GHz)

5 dBi Omni-Directional antenna

Transmit Power

11 dBm

Transmit Range (LOS)

700 m (Typical)

Certification

FCC/FCC ID, CE (RED excluded)

Ethernet Network

Port

x1, 10/100 Base

‐

Protocol

Modbus TCP Slave

Serial port (COM)

RS-232

x1, (TxD, RxD and GND)

RS-485

x1, (D+, D

‐

)

Baud Rate

1200 ~ 115200 (bps)

Data Format

N81, N82, O71, O81, E71, E81, S71, S81, M71, M81

Protocol

Modbus RTU Master/Slave

Polling Definition

Up to 240 Modbus command definitions for all
ZigBee/RS-232/ RS-485 ports

Shared Memory

9600 registers for each of AI, AO, DI and DO data

Institutions

Casing

Metal

Dimensions (L x W x H)

120 mm x 33 mm x 116 mm

Installation

DIN-Rail

Power

Protection

Power reverse polarity protection

EMS Protection

ESD, Surge, EFT

Required Supply Voltage

+10 V

~ +30 V

Power Consumption

5 W @ 24 V

Environment

Operating Temperature

‐

25°

C ~ + 75°

Storage Temperature

‐

30°

C ~ + 80°

Humidity

10~90% RH, Non-condensing

Содержание MDC-211-ZT














































Результаты поиска

Содержание MDC-211-ZT

Отзывы:

ICP DAS USA MDC-211-ZT, Руководство пользователя, Страница: 7 / 46

Результаты поиска

Содержание MDC-211-ZT

Отзывы: