ICP DAS USA MDC-211-ZT Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 46

ICP DAS USA MDC-211-ZT Скачать руководство пользователя страница 15

ICP DAS, MDC-211-ZT user manual , v1.0 Page 14

Copyright © 2018 by ICP DAS. All rights are reserved.

2.3.

Set Port Information

MDC-211-ZT provides one port ZigBee, one port Ethernet, one port RS-232 and one

port RS-485 communication interface, this section introduces the configuration procedure

for these communication interface.



ZigBee Port Setting

Click "Module Setting"

→

"ZigBee", to read the current ZigBee setting parameters, if

user want to adjust the ZigBee settings, click the "Modify" button to switch to the

configuration page, as shown in Figure 2.6.

Figure 2.6 Steps to switch to the ZigBee configuration page

For the description of the ZigBee settings, please refer to section “4.1.1 ZigBee

Communication Interface”. After modifying the setting parameters, please remember to click

"Save" button to save the changes, or click the "Cancel" button to discard the configuration

and return to the previous page.

NOTE

- The new ZigBee settings will take effect immediately after configuration without

restarting the power of the MDC-211-ZT.

1

2

3

4

«
...
13
14
15
16
17
...
»

Содержание MDC-211-ZT















































Отзывы:

Нет отзывов