ICP DAS USA MDC-211-ZT Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 46

ICP DAS USA MDC-211-ZT Скачать руководство пользователя страница 10

ICP DAS, MDC-211-ZT user manual , v1.0 Page 9

Copyright © 2018 by ICP DAS. All rights are reserved.

2.

Getting Started With MDC-211-ZT

This chapter mainly describes the operation process of the MDC-211-ZT, such as, how to use

the MDC-211-ZT Web interface via browser, and set up the Modbus Master and Modbus

Slave function for the Modbus data concentrator.



MDC-211-ZT Setting Flowchart

Preparation

•Hardware wiring
•Set the MDC-211-ZT and PC to the same local area network. (The default IP address of

MDC-211-ZT is 192.168.255.1)

Web Login

•Launch the browser and enter the IP address of MDC-211-ZT
•login MDC-211-ZT (Both the default account and password are "Admin")
•Change a new account/password for higher security

Port

Settings

•Configure communication port settings according to the user needs.

Modbus

Master

•Set the communication interface to Modbus Master according to the actual requirements,

and adjust the related setting parameter values.

•Add Modbus RTU commands to specific communication port for Modbus data

acquisition.

Modbus

Slave

•Set the communication interface to Modbus Slave according to the actual requirements,

and set its Modbus Slave ID.

System

Backup

•Export: Export the MDC-211-ZT setting parameters to a. csv file for backup.
•Import: Import the configurations into the MDC-211-ZT via a .csv file.

Check

Polling State

•Check the polling state of each Modbus commands.
•Get the address mapping table between the remote Modbus RTU devices and Internal

Registers of MDC-211-ZT.

«
...
8
9
10
11
12
...
»

Содержание MDC-211-ZT















































Отзывы:

Нет отзывов