ICP DAS USA IR-310-RM Скачать руководство пользователя

Страница: 16 / 65

IR-310-RM,

IR Controlled 10-ch High Power Relay Module

(Ver. 1.1, Jul/02/2013) 16

2.7 LED Indicators

There are two kinds of LEDs for IR-310-RM to indicate several states.

(1) Power LED :

The PWR LED is ON to indicate the IR-310-RM is turned on.

Figure 2-14: Power LED

(2) Relay State LEDs

These 10 LEDs indicate the states of the 10 relays(RL) where:

Table 2-3 Relay LED and Contact Position

Relay State

Contact Position

RL# ON

Normally Open

RL# OFF

Normally Closed

Figure 2-15: Relay States LEDs

(3) List of LED State

Table 2-4: The State List of LEDs for IR-310-RM

LED

State

Comments

PWR

Power ON / Normal operation mode

PWR

OFF

Power OFF

PWR

Blinking 4 times/s

Firmware update mode

PWR

Blink 2 times/sec

Receiving an IR command

PWR

Blink 1 time

Emitting an IR command by the utility

RL0 ~ RL9

Contact in Normally Open

RL0 ~ RL9

Contact in Normally Closed

ГК

Атлант

Инжиниринг

–

официальный

представитель

РФ

СНГ

+7(495)109-02-08 [email protected] www.bbrc.ru

Содержание IR-310-RM


































































Результаты поиска

Содержание IR-310-RM

Отзывы:

Похожие инструкции для IR-310-RM

Бренды по названию

Популярные бренды

ICP DAS USA IR-310-RM, Руководство пользователя

Результаты поиска

Содержание IR-310-RM

Отзывы:

Похожие инструкции для IR-310-RM

Бренды по названию

Популярные бренды