ICP DAS USA iCAM-721F Скачать руководство пользователя страница 26

Страница: 26 / 88

iCAM-

721F User’s Manual ICP DAS

3.2

Camera Live View UI Setting Tools

The

Live View

UI setting tools (the below figure) offer a variety of methods in

changing the live view configurations of the Camera.

Figure 3-4 Camera Live
View Reconfiguration Tools

Overview of Live View UI

Actual Size / Protocol / Video Stream:

Choice the size, protocol and video stream.

Recording Path / Recording file name:

Specify a storage destination path for the video and define
a base filename for the video you are going to record.

Snapshot Path / Snapshot file name:

Specify a storage destination path for the snapshot images
and define a base filename for the snapshots you are going
to capture.

Setting Language:

Select the default language of the user-interface.

Setup button:

Click

Setup

button can change or update more Camera

settings, including Video & Audio, System, Network,
Event, Local Storage and Remote Storage.

Содержание iCAM-721F

























































































Результаты поиска

Содержание iCAM-721F

Отзывы:

Похожие инструкции для iCAM-721F

Бренды по названию

Популярные бренды

ICP DAS USA iCAM-721F, Руководство пользователя

Результаты поиска

Содержание iCAM-721F

Отзывы:

Похожие инструкции для iCAM-721F

Бренды по названию

Популярные бренды