manualshive.com logo in svg

Icom M506 31, Инструкция по эксплуатации

Поделиться
Скачать
Icom M506 31 Скачать руководство пользователя страница 14

5

2

PANEL DESCRIPTION

New2001

Function display

 

■

t

 CALL CHANNEL ICON 

(p. 9)

  Appears when the Call channel is selected.

y

 DUPLEX ICON 

(p. 10)

  Appears when a duplex channel is selected.

u

 FAVORITE CHANNEL ICON 

(p. 17)

  Appears when a Favorite (Tag) channel is selected.

i

 MESSAGE ICON

  Blinks when there is an unread DSC message.

o

 GPS ICON

 Stays ON when the GPS receiver is activated and valid 

 

➥

position data is received.
Blinks when invalid position data is being received.

 

➥

!0

 SWITCH ICON 

(p. 69)

   Appears when the “CH 16 SWITCH” in DSC Settings is set 

to OFF.

!1

 LOW BATTERY ICON

   Blinks  when  the  battery  voltage  drops  to  approximately 

10.8 V DC or less.

!2

 CHANNEL NUMBER READOUT

  Shows the selected operating channel number.

  •  When a simplex channel is selected, “A” or “B” appears.

!3

 CHANNEL NAME FIELD

  The channel name appears, if programmed. (p. 13)

!4

!6

!7

q w

i

e

t

r

!0

y

o

u

!1

!3

!8

!9

@0

!5

!2

q

 BUSY/TRANSMIT ICON

 (pp. 11, 12)

 The  “

 

➥

”  icon  appears  when  receiving  a  signal  or 

when the squelch is open.
The “

 

➥

” icon appears while transmitting.

w

 POWER ICON 

(p. 11)

The “25W” icon appears when high power is selected.

 

➥

The “1W” icon appears when low power is selected.

 

➥

e

 RX HAILER ICON 

(p. 75)

  Appears while in the RX Hailer mode.

r

 CHANNEL GROUP ICON 

(p. 10)

 The selected channel group icon, USA “USA,” Interna-

 

➥

tional “INT” or Canadian “CAN” appears.
 

 

➥

The “WX”  icon  appears  when  the  weather  channel  is 

selected.

Содержание M506 31





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды