Icom iM506 Скачать руководство пользователя страница 118

Страница: 118 / 124

109

New2001

SPECIFICATIONS AND OPTIONS

New2001

Specifications

■

General

• Frequency coverage:

Tx 156.025–157.425 MHz

Rx 156.050–163.275 MHz

CH70 156.525 MHz

• Mode:

FM (16K0G3E),
DSC (16K0G2B)

• Channel spacing:

25 kHz

• Operating temp. range:

–20°C to +60°C (–4ºF to +140ºF)

• Current drain (at 13.8 V):

TX high

5.5 A maximum

Max. audio 5.0 A maximum

(With EXT SP)

Max. audio 1.5 A maximum

(With INT SP)

• Power supply requirement:

13.8 V

DC ±15%

(negative ground)

• Frequency tolerance:

±10 ppm (–20°C to +60°C;

–4ºF to +140ºF)

• Antenna impedance:

nominal

• Dimensions:

178.9 (W)

113.9 (H)

(Projections not included)

113.8 (D) mm

7 (W)

4.5 (H)

4.5 (D) inches

• Weight (approximately):

1.4 kg; 3.1 lb

Transmitter

• Output power:

25 W/1 W

• Modulation system:

Variable reactance frequency

modulation

• Max. frequency deviation:

±5.0 kHz

• Spurious emissions:

Less than –70 dBc (high)

Less than –56 dBc (low)

Receiver

• Receive system:

Double conversion

superheterodyne

• Sensitivity (12 dB SINAD):

–13 dBµ (typical)

–5 dBµ emf (typical)

(CH70/DSC) (1% BER)

• Squelch sensitivity:

Less than –7 dBµ

• Intermodulation rejection ratio: More than 75 dB

More than 68 dBµ emf

(CH70/DSC) (1% BER)

•

Spurious response rejection ratio: More than 75 dB

More than 73 dBµ emf

(CH70/DSC) (1% BER)

• Adjacent channel selectivity:

More than 75 dB

More than 75 dBµ emf

(CH70/DSC) (1% BER)

• Audio output power:

More than 15 W at 10% distor

tion with an external speaker
(4

load)

All stated specifications are subject to change without notice or obligation.

Содержание iM506





























































































































Результаты поиска

Содержание iM506

Отзывы:

Похожие инструкции для iM506

Бренды по названию

Популярные бренды

Icom iM506, Инструкция по эксплуатации

Результаты поиска

Содержание iM506

Отзывы:

Похожие инструкции для iM506

Бренды по названию

Популярные бренды