Icom id- rp2, Инструкция по эксплуатации

Страница: 2 / 56

2001 NEW
IMPORTANT
READ THIS INSTRUCTION MANUAL
CAREFULLY
before installing or operating the
repeater.
SAVE THIS INSTRUCTION MANUAL.
This
manual contains important safety and operating
instructions for the ID-RP2 system.
EXPLICIT DEFINITIONS
i
WORD DEFINITION
R DANGER!
Personal death, serious injury or an
explosion may occur.
R WARNING!
Personal injury, fire hazard or elec-
tric shock may occur.
CAUTION
Equipment damage may occur.
NOTE
If disregarded, inconvenience only. No
risk or personal injury, fire or electric
shock.
R DANGER!
ID-RP2 installation, particularly ID-
RP2L and antennas, is intended for professional
installation only. We are not responsible for any building
breakage, any damage resulting from a drop of the ID-
RP2L or antenna from a high place or unstable site or
resulting from any personal injury nor any accident in
any other cases. Be sure to consult an expert engineer
for installations.
R WARNING RF EXPOSURE!
This device emits
Radio Frequency (RF) energy. Extreme caution should
be observed when operating this device. If you have
any questions regarding RF exposure and safety
standards please refer to the Federal Communications
Commission Office of Engineering and Technology’s
report on Evaluating Compliance with FCC Guidelines
for Human Radio Frequency Electromagnetic Fields
(OET Bulletin 65).
R WARNING HIGH VOLTAGE! NEVER
attach
an antenna or internal antenna connector during
transmission. This may result in an electrical shock or
burn.
R WARNING HIGH VOLTAGE! NEVER
install the
antenna at any location where a person could easily
touch the antenna during transmission. This may result
in an electrical shock or burn.
R WARNING! NEVER
apply AC to the [DC 13.8V IN]
connector. This could cause a fire or damage the
repeater.
R WARNING! NEVER
apply more than 16 V DC
to the [DC 13.8V IN] connector on the repeater. This
could cause a fire or damage the repeater.
R WARNING! NEVER
let metal, wire or other
objects touch any internal part or connectors on the
repeater. This may result in an electric shock or this
could cause a fire or may damage the repeater.
R WARNING! NEVER
operate or touch the repeater
unit, ID-RP2C, ID-RP2D and ID-RP2V, with wet hands.
This may result in an electric shock or may damage to
the repeater unit.
R WARNING! NEVER
connect the repeater to a
power source using reverse polarity. This will damage
the repeater.
Make sure the repeater power is turned OFF when
connecting a power supply.
DO NOT use or place the repeater unit, ID-RP2C, ID-
RP2D and ID-RP2V, in areas with temperatures below
–10°C (+14°F) or above +50°C (+122°F).
DO NOT
use or place the ID-RP2L in areas with
temperatures below –30°C (–22°F) or above +60°C
(+140°F).
DO NOT place the repeater unit, ID-RP2C, ID-RP2D
and ID-RP2V, in excessively dusty environments or in
direct sunlight.
DO NOT
place the repeater unit, ID-RP2C, ID-RP2D
and ID-RP2V against walls or putting anything on top
of the units. This will obstruct heat dissipation.
DO NOT use harsh solvents such as benzine or
alcohol to clean the repeater, as they will damage the
repeater’s surfaces. If the repeater becomes dusty or
dirty, wipe it clean with a soft, dry cloth.
DO NOT
modify the repeater for any reason.
Place the repeater in a secure place to avoid
inadvertent use by children.
Use the specified fuse only.
For U.S.A. only
CAUTION: Changes or modifications to this repeater,
not expressly approved by Icom Inc., could void
your authority to operate this repeater under FCC
regulations.
CAUTION:
The ID-RP2L is intended for use as a fixed
base station with the antenna located outdoors on the
rooftop or on antenna tower.
PRECAUTIONS