38
■
Set mode items
D
Repeater tone frequency
Select the subaudible tone needed to access the re-
peater. A total of 50 tone frequencies (67.0–254.1 Hz)
are selectable. (default: 88.5 Hz)
D
Tone squelch frequency
Select the CTCSS tone frequency to use for the Tone
Squelch function. A total of 50 tone frequencies (67.0–
254.1 Hz) are selectable. (default: 88.5 Hz)
• Usable subaudible tone frequencies
(unit: Hz)
67.0
69.3
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
131.8
136.5
141.3
146.2
151.4
156.7
159.8
162.2
165.5
167.9
171.3
173.8
177.3
179.9
183.5
186.2
189.9
192.8
196.6
199.5
203.5
206.5
210.7
218.1
225.7
229.1
233.6
241.8
250.3
254.1
The transceiver has 50 tone frequencies and conse-
quently their spacing is narrow compared with units
having 38 tones. Therefore, some tone frequencies may
receive interference from adjacent tone frequencies.
D
DTCS Code
Set the DTCS code (both encoder and decoder) for DTCS
squelch operation. A total of 104 codes are selectable.
(default: 023)
• Available DTCS codes
023
025
026
031
032
036
043
047
051
053
125
131
132
134
143
145
152
155
156
162
245
246
251
252
255
261
263
265
266
271
356
364
365
371
411
412
413
423
431
432
506
516
523
526
532
546
565
606
612
624
054
065
071
072
073
074
114
115
116
122
165
172
174
205
212
223
225
226
243
244
274
306
311
315
325
331
332
343
346
351
445
446
452
454
455
462
464
465
466
503
627
631
632
654
662
664
703
712
723
731
732
734
743
754
D
DTCS Polarity
Set the Transmit and Receive DTCS polarity to “NN,”
“NR,” “RN” or “RR.”
The polarity for transmitting or receiving can be inde-
pendently set. (default: dtP.nn)
TX/RX: Normal polarity
TX/RX: Reverse polarity
D
Frequency offset
Set the duplex frequency offset between 0 and 20 MHz.
In the duplex mode, the transmit frequency shifts up or
down from the receive frequency by the offset amount.
(default: Depending on the transceiver versions)
D
Reversed Duplex function
Turn the Reversed Duplex function ON or OFF (default).
When the Reversed Duplex function is ON, the receive
and transmit frequencies are reversed. (default: OFF)
D
Tuning step
Set the VFO tuning step to 5, 10, 12.5, 15, 20, 25, 30 or
50 kHz. (default: differs depending on the version)
D
Scan resume setting
Select the scan resume option from SCt. 5, SCt. 10,
SCt. 15, or SCP. 2.
• SCt. 5/10/15 : The scan pauses for 5 to 15 seconds, when
a signal is received. (default: SCt. 15)
• SCP.2 :
The scan pauses, then resumes 2 seconds
after the signal disappears.
D
Function key timer
Push
[FUNC](
M
)
to enter the Function mode, and then
push a keypad key to activate its second function.
• While in the Function mode, “
” is displayed on the LCD.
Set the time between when the Function mode is en-
tered, and how long it remains activated after you push
the keypad key to activate its second function.
• F0.At :
Exits the Function mode immediately after a
key is pushed to activate its second function.
(default)
• F1/2/3.At :
The Function mode remains activated 1, 2 or 3
seconds after a key is pushed to activate its sec-
ond function.
• F .m
: The Function mode remains activated until
[FUNC](
M
)
is pushed again, even after a key is
pushed to activate its second function.
10
SET MODES
