Icom ic-m423g Скачать руководство пользователя

Страница: 18 / 110

PANEL DESCRIPTION

■

Speaker Microphone

Microphone

Speaker

IC-M423G/IC-M423GE

/IC-M424G

IC-M423/IC-M424

PTT [PTT]

Hold down to transmit, release to receive. (p. 14)

CHANNEL UP/DOWN KEYS [

]/[

]

Push either key to check Favorite channels, change scan-

ning direction or manually resumes a scan. (pp. 14, 20)

TRANSMIT POWER KEY [H/L]*

➥

Push to toggle the power high or low. (p. 14)

• Some channels are set to only low power.

➥

While holding down [H/L], turn ON the power to turn the
Microphone Lock function ON or OFF. (p. 17)

* [HI/LO] is printed for the IC-M423/IC-M424.

CHANNEL 16/CALL CHANNEL KEY [16/C]

➥

Push to select Channel 16. (p. 11)

➥

Hold down for 1 second to select the Call channel. (p. 11)

• The “CALL” icon is displayed when the Call channel is se-

lected.

*For only the IC-M423G, IC-M423GE, and IC-M424G.

Содержание ic-m423g















































































































Результаты поиска

Содержание ic-m423g

Отзывы:

Похожие инструкции для ic-m423g

Бренды по названию

Популярные бренды

Icom ic-m423g, Инструкция по эксплуатации

Результаты поиска

Содержание ic-m423g

Отзывы:

Похожие инструкции для ic-m423g

Бренды по названию

Популярные бренды