Icom IC-F9011B Скачать руководство пользователя

Страница: 16 / 70

Emergency transmission

When

[Emergency] is held down for the preset time period,

the DTMF emergency signal is transmitted once, or repeat-
edly

, on the specified emergency channel.

A repeat emergency signal is automatically transmitted until
turning the transceiver OFF, or pushing

[Home]

When no emergency channel is specified, the signal is trans-
mitted on the previously selected channel.

If you want to cancel the emergency call, hold down

[Emer-

gency] again before transmitting the call.

If your transceiver is programmed for Silent operation, you
can transmit Emergency calls without the beep sounding or
the LCD display lighting.

IMPORTANT: It is recommended to set an emergency
channel individually to provide the certain emergency call
operation.

Depending on the presetting.

For only transceivers whose revision number is 1.7 or later.

NOTES

Depending on the presetting, the following functions are au-
tomatically activated.

• Auto TX function
The transceiver automatically transmits the microphone audio
for the preset time period after the emergency call transmis-
sion.

- The HM-148G or HM-152

hand

microphone

is required for Mobile

transceivers.

• Auto RX function
The transceiver stands by in the audible mode for the preset
time period, after the emergency call transmission.

ANALOG MODE OPERATION

Содержание IC-F9011B







































































Результаты поиска

Содержание IC-F9011B

Отзывы:

Похожие инструкции для IC-F9011B

Бренды по названию

Популярные бренды

Icom IC-F9011B, Руководство по эксплуатации

Результаты поиска

Содержание IC-F9011B

Отзывы:

Похожие инструкции для IC-F9011B

Бренды по названию

Популярные бренды