manualshive.com logo in svg

Icom IC-F5020 Series, Инструкция по эксплуатации

Поделиться
Скачать
Icom IC-F5020 Series Скачать руководство пользователя страница 6

■

 Function display

q w

e

r

t

y u

i

o

q 

TRANSMIT INDICATOR

 

Displayed while transmitting.

w 

BUSY INDICATOR

 

Displayed while the channel is busy.

e 

SIGNAL STRENGTH INDICATOR

 

Indicates relative signal strength level as below.

Weak 

    

 Receive Signal level 

    

 Strong 

r 

LOW POWER INDICATOR

 

Displayed when low output power is selected.

t

 AUDIBLE INDICATOR

 

➥

  Displayed when the channel is in the ‘Audible’ (unmute) 

condition.

 

➥

  Displayed when the specific 2/5-Tone/MDC* code is 

received.

y

 SCRAMBLER INDICATOR

 

Displayed when the voice scrambler function is activated.

u

 BELL INDICATOR

   Displayed/blinks when the specific 2/5-Tone/MDC* code 

is received, according to the pre-programming.

i

 SCAN INDICATOR

   Blinks during scan.

o

 ALPHANUMERIC DISPLAY

 

 Displays an operating channel number, channel name, 
Set mode contents, DTMF code, and so on.

* MDC operation only (p. 13)

2

1

PANEL DESCRIPTION

Содержание IC-F5020 Series

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды