manualshive.com logo in svg

Icom AP-90M, Инструкция по эксплуатации

Поделиться
Скачать
Icom AP-90M Скачать руководство пользователя страница 80

6

MAINTENANCE

6-6

Firmware version 
information

The AP-90M’s firmware can be updated on the setting screen.

A

 

Manually updating the firmware:

   If you cannot update the firmware online, select the firmware downloaded from the Icom website, and 

then manually update.

B

 

Firmware update online

 (

+

p.6-8):

  The firmware can be updated to the latest version using the internet.

•  You can also update by saving the firmware file on a USB flash drive*, and then update from the drive. 

(

+

p.6-16) 

  *User supplied

TOP

 About the firmware

Firmware is a system programmed into the flash memory to make the AP-90M operate.
This system can be updated to a newer version in order to have more functions, or to improve the firm-
ware.
Before  updating,  access  the  setting  screen  and  check  the  firmware  version  information  on  the  “TOP” 
screen.

 Firmware update note

Never turn OFF the AP-90M during a firmware update.

 

➥

  This will cause the data to be lost or corrupted.

 If you have the Firewall security system enabled, and the firmware cannot be updated, disable the sys-

 

➥

tem.

• The updating the firmware is your responsibility.

   Read the following information carefully, and then access the Icom website (http://www.icom.co.jp/world/) to download 

the AP-90M’s firmware update file.

   Icom is not responsible on the consequences of updating the firmware.

4. Firmware Update

Содержание AP-90M








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды