Icom AP-90M Скачать руководство пользователя страница 78

Страница: 78 / 103

MAINTENANCE

6-4

If you want to reset or change the network system, you can clear and restore all the settings by resetting to
the factory defaults.
There are two ways to reset:

Pushing [MODE].

When the setting screen cannot be accessed because the IP address or the password set to the AP-90M

is unknown.

Using the setting screen (

p.6-5)

Pushing [MODE]

Disconnect all the connected devices from the
AP-90M, and then turn ON the power.

• Make sure the [POWER] and [WIRELESS] (1/2) indi

cators are lit, and then go to step 2.

• Except for [POWER], the indicator status may differ,

depending on the environment.

• If the AP-90M is mounted on a wall using the supplied

mounting bracket set, the [MODE] button cannot be
pushed.

See MB-102 instruction manual for mounting informa-

tion.

Hold down [MODE] until all indicators light orange

, and then release it when all indicators are lit

orange . The resetting is complete.

Attach

Release

Hold down

Light (orange)

Lights (Green)

Blinks (orange)

All light (orange)

Blinks (orange)

Lights (Green)

Light (orange)

AP-90M

WIRELESS A

CCESS POINT

: No light

[Indicator status]

Indicator transition while resetting

: light

: Blink

NOTE:

After resetting, the IP address is reset as the default. (http://192.168.0.1/)
If you cannot access the AP-90M, change the PC’s IP address.

3. Restoring the factory defaults

Содержание AP-90M








































































































Результаты поиска

Содержание AP-90M

Отзывы:

Бренды по названию

Популярные бренды

Icom AP-90M, Инструкция по эксплуатации

Результаты поиска

Содержание AP-90M

Отзывы:

Бренды по названию

Популярные бренды