manualshive.com logo in svg

Icom AP-90M, Инструкция по эксплуатации

Поделиться
Скачать
Icom AP-90M Скачать руководство пользователя страница 50

3

CONNECTING TO A WIRELESS LAN (BASIC)

3-18

Wireless Settings > Wireless 1 > Wireless Bridging (WDS)

Wireless Settings > Wireless 2 > Wireless Bridging (WBR)

Management > Management Tools

 Setting the wireless bridging function to the AP-90M for the RS-AP3 management

q

  Set the wireless bridging function on the AP-90M setting screen (Wireless 1 or Wireless 2) to enable the 

communication.

w

 Enable “Management Tools” on the setting screen.

e

  Before start the access point management using the RS-AP3, set the AP-90M setting values on the “In-

dividual Configurations” screen* of the RS-AP3.

  *  If you want to use the wireless bridging function in Wireless 2, configure the master unit’s SSID and 

security settings on the “Common Configuration” screen.

6. Setting the Wireless Bridging function (Continued)

Wireless 2:
Master settings on the “Common Configuration” screen.

Wireless 2:
“Common Configuration” screen.

Wireless 2:
Client settings on the “Individual Configurations” screen.

Содержание AP-90M








































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды